BITI Built
BITI Dash
🏍️
Connect over Bluetooth to your controller.
Live Gauges –
—
Drivetrain
–
Motor RPM
–
Output Torque Nm
–
Phase Current A
–
Throttle %
◭ Wheelie / IMU Module
–
Pitch °
–
Gyro
–
Lift Nm
The factory wheelie-assist is disabled on your bike (reg 263). Enable & tune its PID in the Tune tab → IMU / Wheelie.
Power & Speed
–
kW NOW
–
kW PEAK
–
km/h PEAK
Bus Voltage & Current
Temperatures
■ Motor
■ Controller
THROTTLE 0%
0°30°60°90°
–
Set / Target °
–
Lift Torque Nm
0.0s
Wheelie Hang Time
– A
Phase Amps
– W
Power (watts)
0.0s
Best Wheelie
–°
Session Peak Angle
–
Wheelie Assist
The controller reads your pitch angle live from the onboard IMU. When Wheelie Assist is on, it uses a torque loop to help hold the front wheel near your set angle — pull it with the throttle at 100%.
• Status — DISABLED (assist off, angle still shown) · ARMED (on, wheels down) · ENGAGING (assist applying lift torque).
• Set angle & band and the on/off switch live in the Tune tab → ◮ IMU / Wheelie group (PSetPitchAngle, PPulleyWheel). Change them there, then Save to Bike.
• The IMU must read online for assist to work.
• Status — DISABLED (assist off, angle still shown) · ARMED (on, wheels down) · ENGAGING (assist applying lift torque).
• Set angle & band and the on/off switch live in the Tune tab → ◮ IMU / Wheelie group (PSetPitchAngle, PPulleyWheel). Change them there, then Save to Bike.
• The IMU must read online for assist to work.
🏁 DRAGYGPS PERFORMANCE
Come to a stop, then ARM. Launch when the tree goes green — timing starts automatically on movement.
GPS —
🏆 Leaderboard
Compare bikes, tunes, tires & riders.
⚠ Editing your tune can permanently damage the motor or controller, or brick the bike if done wrong. Always tap “Backup Tune” first so you can restore it. Read-only until you flip the switch below; values write one at a time with confirmation. You tune at your own risk.
Enable Writing
Off = safe read-only browsing
Edits apply live as you make them, but revert on power-off until you Save. This writes the full tune to the controller’s flash memory.
272 parameters · reg = index × 2 · word-order —
READY
0
SAMPLES LOGGED
0:00
DURATION
0 KB
EST. SIZE
Sample Rate
8 Hz
Every telemetry channel is captured per sample.
Live Snapshot
Freeze-frame fault records stored in the controller (FLASH2, read-only). Each is a full snapshot of the bike at the instant a fault tripped — voltages, currents, temps, speed, odometer.
Connect and read to load the two most recent fault records.
⚠ Firmware flashing can brick the controller. Before you start: bike on a stand, battery charged / on a charger, phone right next to the bike, and do not power off, close this tab, or walk out of Bluetooth range until it finishes. If it fails, power-cycle and re-flash the same file — or recover with the official app.
1 · Firmware file (.bin)
No file selected.
2 · Your controller
Connect to read controller type & version.
The app can’t read type/version from an encrypted .bin — you must be sure this file is for THIS bike (the filename should match your controller).
3 · Flash
Arm — I understand this can brick the controller and I have a recovery plan.
Flash Log
Idle.
Account
Signed in–
Status–
Tune editing–
Units
Theme
Text Size
My Bikes
Bikes you've connected to are saved here. Rename them, and the app auto-connects when one is nearby.
About
BITI Dash · BITI Built. A tool for your own hardware — all your settings, bikes and tunes are stored on this device.